Furnace Size Calculator from Your Gas Bill
This furnace size calculator uses your actual gas bill to estimate how many BTU/h your home needs on the coldest design day. Your bill records how much heat the house really lost over a known period, so it often gives a more grounded answer than the “BTU per square foot” rules of thumb that leave so many Ontario homes with oversized furnaces.
How the furnace size calculator works (formula)
- Remove non-heating gas: heating m³ = bill m³ − (baseload m³/day × days). The baseload covers your water heater, stove and dryer.
- Convert to heat delivered: BTU = heating m³ × 37.5 MJ/m³ × AFUE × 947.817 BTU/MJ.
- Heat loss coefficient: UA = BTU ÷ (days × 24 h × (indoor temp − average outdoor temp)). This gives BTU/h per °C of temperature difference.
- Design heat load: UA × (indoor temp − outdoor design temp).
- Furnace input: design load ÷ AFUE, then rounded up to the next common input size.
Furnace size calculator inputs and their sources
- Indoor 22°C: Ontario Building Code Article 9.33.3.1 requires heating systems to hold living spaces at 22°C or more at the outside design temperature.
- Outdoor design temperatures: the January 2.5% values from MMAH Supplementary Standard SB-1, which OBC 9.33.3.2 requires for sizing. Examples are Toronto City Hall −18°C, Ottawa −25°C, Hamilton −17°C, London −18°C, Sudbury −28°C, Thunder Bay −31°C and Windsor −16°C. Read the current standard in the 2024 Ontario Building Code.
- 37.5 MJ/m³: the natural gas energy content used by Statistics Canada and NRCan.
- Average outdoor temperature: look up your billing dates in Environment Canada historical climate data.
Worked example: furnace size from a January gas bill
A Toronto home used 330 m³ over a 31-day January billing period. The average outdoor temperature was −5°C, the furnace is 95% AFUE, and summer bills show about 2 m³/day for the water heater and stove.
- Heating gas: 330 − (2 × 31) = 268 m³
- Heat delivered: 268 × 37.5 × 0.95 × 947.817 = 9,049,283 BTU
- UA: 9,049,283 ÷ (744 h × 27°C) = 450.5 BTU/h·°C
- Design load at −18°C: 450.5 × 40 = 18,019 BTU/h
- Furnace input: 18,019 ÷ 0.95 = 18,968 BTU/h, so the smallest common size of 40,000 BTU/h input is more than enough.
Many homes like this one have an 80,000–100,000 BTU/h furnace. Oversizing leads to short cycling, uneven temperatures and extra wear. If your bill seems high for the house, read why your gas bill is high in winter. If you are thinking about switching fuels, try our HVAC tools.
Getting the most accurate furnace size estimate
The quality of the answer depends on the bill you choose. Pick a billing period with an actual meter reading, not an estimate, ideally in January or February when heating dominates. If you have several winter bills, run the calculator on each one and compare the design loads. They should agree to within roughly 10–15%. A result far from the others usually points to an estimated reading, a holiday away from home or an unusual baseload.
Ask your contractor to compare their F280 result with this estimate. If the F280 load is far higher than what your gas bills suggest, ask which assumptions about air leakage, insulation and windows drive the difference. Oversized furnaces cost more to buy, cycle more and can be less comfortable. Right-sizing also matters if you plan to add a heat pump, because the heat pump’s capacity at your design temperature should be compared against this load.
Assumptions and disclaimer
- This is a screening estimate, not a CSA F280 heat loss calculation. Permits and proper equipment selection need a room-by-room F280 done by a qualified designer.
- Use your coldest full billing period. Mild months with estimated readings give poor results.
- Heat from people, appliances and sun lowers the bill, so the method slightly underestimates the load. Thermostat setbacks have a similar effect.
- The AFUE you enter should be your current furnace’s real efficiency. An old furnace with a high rated AFUE will overstate the load.
- The SB-1 values shown come from the 2012 standard as amended. Confirm them against the edition your municipality enforces.
Disclaimer: for education only. Have a licensed HVAC contractor size and install your equipment.
Furnace size calculator FAQ
How do I find my baseload?
Take a summer bill, when the furnace is off, and divide its m³ by its days. A gas water heater alone often uses 1–3 m³/day.
Why is the result smaller than my current furnace?
Older furnaces were often sized with generous rules of thumb, and many homes have been air sealed or insulated since. A smaller, properly sized furnace runs longer, steadier cycles.
Can I use this to size a heat pump?
The design load in BTU/h is a reasonable starting point for comparing heat pump capacity at your design temperature. Check the model’s capacity at that temperature, not just its nominal rating.
Which outdoor design temperature should I use?
Use the SB-1 January 2.5% value for your municipality. The building code requires these values for heating system design.
