Natural Gas Pipe Sizing Calculator: Free Step-by-Step Tool

Natural Gas Pipe Sizing Calculator (Longest-Length Method)

Study and estimating tool. Capacities are from IFGC Table 402.4(2) (Schedule 40 steel, natural gas, under 2 psi, 0.5 in. w.c. pressure drop, 0.60 SG). In Canada, the CSA B149.1 pipe sizing tables in your code book govern – always check your answer there.
1,000 is the value IFGC uses to convert BTU/h to ft³/h.

Use this natural gas pipe sizing calculator to find the minimum Schedule 40 steel pipe size for a low-pressure residential gas system using the longest-length method. Add your appliances, enter the run from the meter to the farthest appliance, and switch on G3 study mode to see every step written out, the same way you would work a sizing question on a gas technician exam.

How the natural gas pipe sizing calculator works

  1. Total connected load: add up the BTU/h input of every appliance from its rating plate.
  2. Convert to flow: ft³/h = BTU/h ÷ 1,000 (the heating value assumed by the table).
  3. Longest length: measure from the meter outlet to the farthest appliance. Metres are converted at × 3.28084. Always round up to the next table row, never down.
  4. Read the table: on that row, move across to the first pipe size whose capacity is at least your flow.
  5. Branches: with the longest-length method, every section is sized from the same row using only the load that section carries.

Pipe sizing table used (and why B149.1 governs)

The capacities come from IFGC Table 402.4(2): Schedule 40 metallic pipe, natural gas, inlet pressure under 2 psi, 0.5 in. w.c. pressure drop and 0.60 specific gravity. Lengths run from 10 to 350 ft, and sizes from ½” to 3″. At 60 ft, for example, the capacities are ½” 65, ¾” 137, 1″ 257 and 1¼” 528 ft³/h. The table is published in the International Fuel Gas Code.

In Canada, gas piping must meet CSA B149.1 (CSA Group). Its tables are similar in method but may differ by pipe type, pressure and units. Use this tool to learn the method and check your work, then confirm the size in your code book. Our B149.1-25 code book guide shows where the tables are.

Worked example: natural gas pipe sizing for three appliances

Take a house with a furnace, a water heater and a range. The appliance ratings below are sample values:

  • Furnace 80,000 + water heater 40,000 + range 65,000 = 185,000 BTU/h
  • 185,000 ÷ 1,000 = 185 ft³/h
  • Longest run: 60 ft, so use the 60 ft row. A run of 18 m is 59.1 ft, which also uses the 60 ft row.
  • ¾” carries 137 ft³/h, which is too small. 1″ carries 257 ft³/h ≥ 185, so the main from the meter is 1″.
  • Branch to the furnace (80 ft³/h, 60 ft row): ½” = 65 is too small and ¾” = 137 works, so the branch is ¾”.

Need a refresher on terms like “longest length”, “specific gravity” or “w.c.”? See our gas technician glossary.

Common natural gas pipe sizing mistakes

The most common error is measuring the run to the appliance being sized instead of to the farthest appliance. The longest-length method always uses the distance from the meter to the most remote outlet. The second is rounding the length down to a closer row. The third is forgetting future appliances. If a homeowner plans to add a barbecue, a fireplace or a generator later, include that load now, because upsizing the main from the meter is much cheaper during the original installation.

Also check the meter and regulator capacity. Even a correctly sized pipe cannot deliver more gas than the meter set is rated for, so the utility may need to upgrade it when you add a large load. Finally, after installation, a pressure test and leak check to code are mandatory before any appliance is lit, and every joint must be leak-tested with an approved solution or detector.

Assumptions and disclaimer

  • This tool covers natural gas only. Propane uses different tables.
  • It covers Schedule 40 steel only. CSST, copper and polyethylene each have their own tables.
  • It assumes system pressure under 2 psi and an allowable drop of 0.5 in. w.c.
  • Fittings are treated as included in the longest-length method, which is the table’s standard assumption.
  • The appliance values in the example are samples. Always use the rating plates.

Disclaimer: this is a study and estimating aid. Gas piping must be designed and installed by a licensed gas technician to CSA B149.1 and your provincial regulations (TSSA in Ontario).

Natural gas pipe sizing FAQ

Why do I round the length up?

Capacity falls as length increases. Using a shorter row would overstate capacity and could leave appliances short of gas.

Why divide by 1,000?

Pipe sizing tables list flow in cubic feet per hour. Natural gas is taken as about 1,000 BTU per cubic foot for the conversion.

Can I use this for my G3 or G2 exam?

Yes, for practice with the method. Exam questions use the B149.1 tables, so check that your answers match the code book.

What is the longest-length method?

You size every section of the system from the row for the distance to the farthest appliance. It is simple and conservative.