CSST Gas Piping: What It Is, Where It Can Go, and Why Bonding Matters

CSST gas piping is the flexible yellow tubing that carries natural gas or propane through many modern homes. CSST stands for corrugated stainless steel tubing: a thin-walled stainless steel tube with ridges like an accordion, usually covered in a yellow or black plastic coating. It bends around corners and snakes through floor joists the way rigid black pipe never could, which is why installers like it, especially in retrofits. But it is not the same thing as the flexible connector behind your stove, and the code treats it very differently. This article explains what CSST gas piping is, where it can and cannot go, and why bonding matters so much for it.

What CSST gas piping is

Think of CSST gas piping as piping that behaves like a cable. It is a continuous run of corrugated stainless steel, with factory-made fittings at each end, and it carries gas at the same pressures as the rest of the house piping. The corrugations let it bend, so a run that would need a dozen elbows in black pipe can be a single length of CSST with far fewer joints. Fewer joints means fewer places for a leak to start, which is a real advantage.

The tubing and its fittings have to meet a specific standard, ANSI LC 1/CSA 6.26. That is the code’s way of saying not every flexible stainless tube on a shelf is gas piping. If it is not certified to that standard, it does not belong in a gas system.

CSST is not an appliance connector

This is the mix-up that causes the most trouble, because the two products look alike. Behind a gas range or a clothes dryer there is usually a short corrugated metal connector, and the code allows that connector to be up to 6 feet long for a range, refrigerator, clothes dryer, or built-in counter appliance. That connector is a different product, certified to a different standard, and it is built to be disconnected when the appliance moves.

CSST gas piping is not that connector, and the code says so plainly: CSST shall not be used as a gas connector. CSST is fixed piping inside the walls and floors. It does not get pulled out, moved, or flexed every time an appliance is serviced. If you see CSST used as the final flexible link to a stove or dryer, that is not what it is for, and it needs a licensed technician to look at it.

Where CSST gas piping can and cannot go

CSST has a short list of places it belongs and a short list of places it does not.

It can run through a house as part of the fixed gas piping system, and it can connect to an appliance that is secured in place and never moves, or to rigid piping. That covers most furnaces, water heaters, and fireplaces, which are bolted down and stay put.

It cannot be used to connect to a gas meter, unless the meter assembly is independently supported. A meter hanging on the end of a flexible tube is a bad idea: the tube is not a support, and any movement or load on the meter stresses the connection. The same logic applies at the appliance end. CSST connects only to appliances that are fixed in place or to rigid pipe, never to something that moves, rolls, or gets pulled out for cleaning.

Why bonding matters for CSST gas piping

Bonding is the most important safety rule for CSST, and it exists because of lightning. The stainless wall of CSST is thin, which is what makes it flexible. A lightning strike nearby can push a surge of electrical energy through a house, and if that energy finds the thin wall of the CSST, it can burn a hole through it. Gas escaping from that hole is how fires start. Bonding gives that energy a safe path to ground instead.

The code’s bonding rule for CSST is specific. Unless the CSST system is certified to protect against lightning strikes on its own, it must be bonded following the manufacturer’s installation instructions, with a bonding conductor connected to each end of the CSST run, or connected to the inlet end with the other end run to the appliance disconnect switch or the electrical distribution panel. One detail matters a lot: the bonding clamp goes on the rigid pipe or tubing connected to the CSST, never on the CSST itself. Clamping to the corrugated tube can damage it and defeats the purpose.

There is a related rule for the rest of the gas piping too. Interior metal gas piping connected to a gas-fired appliance that has an electrical connection must be electrically continuous and bonded to the electrical system, normally with a number 6 copper or number 4 aluminum bonding conductor, and the connection must stay accessible after the installation. If you can see a bonding clamp and a bare copper wire near where the gas line enters the house, that is what you are looking at.

Protection, supports, and sizing

CSST is tough for its weight, but it is not armour. The code requires CSST and its fittings to be protected against physical damage, following the manufacturer’s certified installation instructions and the code. In practice that means keeping it out of places where it can be nicked, crushed, or punctured: away from nails and screws in walls, shielded where it passes through joists and studs, and protected where it runs in areas that see traffic or storage. A kinked or dented length of CSST is not a cosmetic problem. A kink weakens the wall and restricts flow, and damaged CSST should be assessed by a licensed technician, not straightened out and ignored.

Sizing is different from black pipe as well. CSST is not sized from the standard pipe sizing tables. It is sized using the sizing methods and tables supplied by the manufacturer, because the corrugations change how gas flows through it. A run that looks like the right size on a black pipe chart can be undersized in CSST, which is one more reason this is licensed work, not a homeowner project.

What to check in your own home

You do not need to be a technician to spot the warning signs. If your house has CSST, it is usually visible in the basement or utility room as yellow or black coated tubing running along joists. Look for these things:

  • A bonding wire connected near the CSST run, with the clamp on rigid pipe, not on the corrugated tube itself. If you cannot find any bonding at all, that is worth a call.
  • CSST running to a stove, dryer, or other appliance that moves. CSST should end at rigid pipe or at a fixed appliance, with a proper appliance connector making the final link.
  • CSST connected directly to the gas meter without the meter being independently supported.
  • Kinks, dents, or damage to the coating, or CSST running unprotected through a wall where nails or screws could hit it.

None of these checks involves touching a gas fitting. Look, do not touch, and do not try to fix anything yourself.

When to call a licensed technician

Call a TSSA-licensed technician if you find CSST with no bonding, CSST used as an appliance connector, CSST feeding a meter that is not independently supported, or any CSST that is kinked, dented, or damaged. Call as well if you smell gas at any time: leave the house, do not flip switches or use a phone inside, and call your gas utility or emergency services from outside.

In Ontario, gas work must be performed by a TSSA-licensed technician. CSST looks simple because it bends, but the rules around bonding, protection, and sizing are exactly what keep it safe, and they are easy to get wrong. A licensed technician works to the current edition of the code, CSA B149.1:25, which Ontario adopted on June 1, 2026. The requirements described here come from the code, and your technician will confirm them against the current edition for your installation.

CSST gas piping is good piping when it is installed to the rules. The failures almost never come from the tubing itself. They come from the shortcuts: no bonding, the wrong fitting, or the wrong job for the product. Know what it is, know what it is not, and let a licensed technician handle the rest.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *